Reproduced courtesy of the information provided here, Pettit paints company. This information reproduced wholesale marine 26 March 2010.
A general description
-Protection of all types of boats reliable and affordable price
-Effects of salt water with fresh
Ideal for boat-TRAILERED
at the bottom of the ship unepoxy hard protective defense antifouling coating is used. It can be applied to most outdated hard proof antifouling paints. You must delete the old soft proof antifouling paint best bond. It is applying fiberglass overboard. Or drive unit itself coating is the outdrives offer electrolytic, danger. all non-aluminum unepoxy also retrailering prior to use in the period of 2 weeks of salt and fresh water is suitable for trailered boats. unepoxy adhesion and excellent non-standard fiberglass, wood, steel hull and is ideal for both power and sail boats. Without fear of all properly hard under-coating fee lifting ready compatibility allows safe overcoating.
Application information
includes unepoxy cuprous oxide. May occur as a result of this, in particular, to paint shelves several months have been settling tendency. It is necessary to mix the paint before you can use to thoroughly. Can shake, mechanical paint Shaker cans of paint. Can do to make sure that the side and bottom before you can use to check all the pigment mixture. Mixture will carry wooden paddles or electric drill mixers, pigments and pour the liquid from the top half of another one you can cans, settled in to properly mix; In part two of the remix thoroughly. Complies with all application instructions, cautions, conditions and restrictions on optimal performance. If you use such as technical sheet products for individual labels and detailed instructions, see. Unepoxy more than 10% (per gallon 12 ounces) is light or or cause insufficient coating thickness and early erosion, finishing and seen.
Surface preparation
The performance of the coating, generally proportional to the degree of surface preparation. Recommendations carefully and avoid shortcuts to run. Guarantee the performance of inadequate preparation of surface virtually insufficient coating.
COVERAGE.....425 sq ft / GAL.
Application data
Method c..Brush, roller and airless or
Conventional spray
coats....Two so far
PER the dry of film thickness circuitry... 2 mil
PER the wet of film thickness circuitry... 4.3 mil
Application TEMP....40 degrees F. min / 90 ° F. Max.
Dry time (hours)
To start the Recoat
90 ° F 3 of 3
70 Degrees F 6 6
40 ° F 12 12
Is the above dry times minimum. starts picture after 60 days, indicating the unepoxy, minimum time, corrosion fouling and recoated may.
evenly distributed by toxicants in entire cans to mix paint to ensure thorough. You must prepare all the surfaces clean and dry the picture before appropriately. Not apply to Unepoxy aluminum.
Painted surface: before coating are in good condition, 80 thorough sand if previous paper by 120 Brushing clean solvent paint thinner residue to remove the grain. Apply a fill finish Unepoxy twice. Before paint soft or polished bare surface in a very bad state, or, using the Pettit roofs bio-blasting paint Remover removes. Naked appropriate systems, proceed as follows. Old Tin copolymers of deletion or-Pettit 6627 must be sealed before applying the Unepoxy Thailand coat primer and corrosion fouling.
Bare fiber glass: regardless of age, all naked fiberglass thoroughly several times and Pettit 1995 to fiberglass Dewaxer clean should be. Thoroughly dull, frosty finishing 80 grain sandpaper, sand, and the rewash 95 fiberglass Dewaxer to remove a sandy surface polishing residues. [Unepoxy application instructions, apply two coats of the standard. Useful for long term bonding after careful observation, follow these steps and antifouling paints. To eliminate the grinding operations, and three times using only Pettit 95 Dewaxer wash glass fiber. Then, apply one Pettit 6999 Sandless primer coat. To Sandless introduction to labels, see defense antifouling coating instructions and complete application.
Bare trees: all sand surface 80 grain on paper; To 120 clean washing brush is thin. Unepoxy coats thinned apply for 25% 120 brushing thin, light sand, clean wipe allow to dry overnight. Apply a fill finish Unepoxy twice.
Residues of bare steel Sandblast SSPC SP 6 commercial blast on a clean, compressed air to blow, and 4700 / doors to follow the instructions of applications and recoat immediately fill twice. Clears from sandpaper or hands Handtool power in clean, damp sand, 80 grain residues clean compressed air or clean, solvent rags. Immediately and apply one Pettit 6980 Rustlok steel primer coat, and dry tack free State 30 minutes can usually 2 hours the temperature relying. [-4700 / Statistical protection Pettit recoat with high build epoxy application instructions apply fill twice a primer. Apply the Unepoxy two coats.
keels-lead: screen with light metals; Clean using abrade wipe Pettit 120 brushing paint thinner. One thin coat 13707 / 044 gold metal primer is applied. 2 Hours to dry. -Pettit 6627 one Thailand coat primer coat, and then apply epoxy fairing compound fairing is required. 6627 Performs Thailand coat primer label directions for each additional coat. Apply a fill finish Unepoxy twice.
keels-steel or cast iron: screen light metals; Clean using abrade wipe Pettit 120 brushing paint thinner. Only 1-2 introduction to 6980 Rustlok steel can dry time overcoating ago one court to apply. The fairing is required if the epoxy and Pettit 6627 Thailand coat primer single court then apply fairing compounds. Apply a fill finish Unepoxy twice.
Maintenance
You cannot effectively under all conditions and antifouling paints exposure. Contamination man and interfere with the performance of natural occurrences defense antifouling paints. Extreme hot and cold seawater temperature, silt and dirt, oil, brackish water and electrolytic to ruin defense antifouling paint that can. Therefore, to determine whether or not it in under the boat clean, we strongly recommend that no growth is checked on a regular basis. To remove something from the Defense antifouling paint surface scrub lightly down with a soft brush. Scrub is particularly important in the boat in an idle state for a long time. If you regularly use the boat coating is the most effective.
No comments:
Post a Comment