How to apply the Interlux Goldspar satin varnish

Goldspar satin Interior material surface is a design change low gloss polyurethane varnish applications. Excellent handling qualities enable truly professional results.

Alcohol stainsAlso resistance proposed best cabinets in wounds and home interior cabin interior counters such as warm, rich glossy tablesProduces finish top, furniture, panelled bar

Preparation
Bare trees: 80 grade (grain) paper and sand. Wipe the LCD 333 brush. Reduce varnish 10% applies to court sealer brushing liquid 333.
120-150 VARNISHED previous tree: dust on the surface of the sand paper grade (grain) and remove the good condition of all. If the bad conditions varnish severely turned on, or on the detachment, wood Interstrip Semi-Paste 299E in naked removes finish. Follow these steps for the varnishing of bare trees.

Until you are satisfied with finishing to at least 5-6 to apply bare how previously coated wood and at least 3 coat surfaces varnished. Each coat 220, student (grain) paper between sand the. Remove the rag grinding residues dampened with brushing liquid 333.

Application
The application on a large flat surface is effective varnish brush to apply, the best way is usually. Along with solid stroke [using whole grains to screen buffs hold brush to 90 degrees. Finally, following grains at 45 degree angle surface to brush gently stroking and tips. Only for use with varnishing brush.

Perform label always specified as the recommendations of the system; this indicates the minimum number of required court or court between the Polish best practices. This information varies depending on the product. To achieve long-lasting protection, you must apply to up to ten court depends on the system. Court number grows, coated fine grain between increases in the depth of the polished glossy and shiny.

Tips
Thinner brushes-the liquid 333 brush. Spray-special thin 216.
Cleaner that wood-special thin 216.
It is recommended to paint dry ventilation and moisture control warm in the morning. You can dry, spoil to delay the cold and humidity, glossy. You should rub the good ventilation, apply effects to the drying time.
Airless spray pressure: 170 bar / 2500 psi. Tip size: 0. 33 0.41 mm/13-16 thou.
Conventional spray pressure cooker: pressure: 3. 44 4... 94 bar / 50-65 psi (County pressure); 8-10 psi (pressure cooker). Tip size: 1. 0 1.4 mm/40-50 thou. Siphon Cup: pressure: 3... 44 4... 94 bar / 50-65 psi – County pressure. Tip size: 1. 5 ~ 1. 8 mm/60-70 thou.
Brush held varnishing specifically using brush clean always. Use the brush before clean.
Roller rolling, clean light NAP roller and use "chip" as soon as natural as the brush bristles.
Other spray pressure listed recommendations only. Applicator, individual spraying techniques and can use all the settings yield results suitable for current weather conditions. To enhance the appearance of a porous open grain of bare wood and fill, you can apply and follow the label instructions Interstain overnight drying.

Excessive wet film thickness over some important point of 5 Mills (WFP) has uneven gloss could be bad. You do not leave public bare wood for long time trying to absorb the moisture. Is this age, in the Middle, and introducing a pollution cans and cans from straight avoid Goldspar satin can. Carefully follow the appropriate drying time is improper drying, crease and adhesion loss occurs. Painting, avoid direct sunlight. Need to minimize the temperature 10 products of 50 ° F and I. , And up to 85 degrees to minimum f. F. ambient temperature 50 degrees. The up to 95 degrees F, substrate temperature 50 ° F to minimum and must be up to 85 degrees F..

Only the surface of the compatible / Board correctly apply to prepare a clean, dry,. With it, and clean the sanding unless Goldspar satin, varnish can be applied. Two part varnish Goldspar satin does not apply.

Court number at least 5-6 to bare wood coat 10% of the first coating: thin

DFT recommended
Application method airless spray, brush and spray on a traditional – pressure cooker or siphon Cup

The information provided here is Interlux courtesy reproduce. Wholesale Marine's reproduction 17 May 2010 to this information.

This entry was posted 05 / 17 / 2010 11: 17 a.m. Monday, and submit a guide under the paint how. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response from your own site, or trackback.

View the original article here