A general description
Originally development of wooden boats, these apply to fi berglass over existing cloisonne old favorites are properly prepared, metal. They also very known application simple, permissive, stunning cover properties, good gloss, season of durable and economical value. Recommended constant immersion.
Application information
Before you can use to thoroughly ??????. Shipendec, brushes, rollers, may be applied in traditional or airless spray. Thinning on the application of the brush or roller application with no heat 5-10% / Pettit 120 thin brushing, wet of can be added to maintain edge. Best results a smooth surface on a large immediately after deployment on the brush adjustment off, please use the short NAP roller. Conventional spray application is 15-20% / Pettit 121 pale and thin sprayed. Apply one of the day also thin coat. After overnight dry, lightly 220 grain paper and stripped and sand, and then apply a second coat. To remove airborne particles in the air may always settled, right in front of a fresh application paint wipe tack cloth. 1 Coat, in two or more applications or overly heavy film (4 wet mill larger) to apply the insuffi cient lead paint drying, and generates a soft paint fi lms. Airless spray application of thin Pettit 121 spraying thin, up to 5%..011-.015 leverage inch diameter tip application. Shipendec, very hot and humid, not apply if you have or rain likely. Wet for at work outdoors as a film negative dew does not apply in the evening you may receive the. And always work in the temperature of the cooler air and surface temperatures over 50 ° will leave at least 8 hours after application.
Surface preparation
You must to free surface dirt, loose paint, rust, oil, grease, wax, SOAP and other foreign matter. 2 Gallon per cup household ammonia water solution in painted with washing area clean and rinse well. Delete the existing mold instead of household bleach ammonia.
System
You must prepare all the surfaces clean and dry the picture before appropriately. Before you can use the enamel ?????? thoroughly. New sand coat enamel 220 grain between the paper. To remove airborne particles in the air may always settled, right in front of a fresh application paint wipe tack cloth.
Bare fiber glass: to draw regardless of age, removing all traces and wax mold spray the entire surface is to, thorough cleaning fibreglass Dewaxer 95 in need. The gelcoat and 80 to 120 grains of sand paper to remove clean residue to the dull, a frosty appearance solvent. If the surface is in good condition, go to the first finishing coat Shipendec.
If surface is rough or defect is repaired. All spills to fill, and epoxy fairing compound foam or 7191 Easypoxy Mender sand Flash is difficult, and clean with solvents are not. Run the Undercoater, uniform base sand to provide clean solvent 8371 Easypoxy white surface and smooth coat. Go to the first finishing coat Shipendec.
To remove a clean residues of bare trees sand surface 80 to 120 in grain paper solvents is smooth. All the screwheads and small hole 7191 Easypoxy Mender sand Flash or solvents enter clean. 2018 Apply a coat of sealer to seal porous grains and penetrate into the clear. Equally smooth basic conditions reach 6165 yacht white Undercoater performs one or two coats; Each coat clean sand paper and solvent 80 to 120 grains. You can blend impressive contrast between the two colors like there is no Undercoater Fi answerma nish enamel. Go to Shipendec fi resort fi answerma nish coat. you need to thoroughly scrub sanding ammonia water and solutions and cleaning solvents paper being epoxied bare wood are 120 grains. Run the Court Undercoater 4169 Easypoxy white surface smooth and to provide a uniform basis. Clean up coats solvent Shipendec Fi resort sand and continue.
Bare steel: need to clean bright fi surface sandblasting or residue removal blasting grinding finish. Just apply one 6980 Rustlok primer coat. You can to dry until tacky. If the surface is rough applies solvent coating clean 6,172 Thailand coat primer sand too. Repeat as necessary until the application is completely smooth, uniform base. First coat Shipendec to continue.
Wipe the free surface in the bare aluminum boats, mast & Spurs: oil and grease solvent. Surface during grain Emery cloth remove removes oxide etch polishing residues. Thin wet coat 13707 gold metal primer allow at least 2 hours to dry apply. Continue Shipendec Fi resort courts. 8371 Surface smoothing if necessary, 13707 gold metal primer on Easypoxy white Undercoater with you.
Surface coating: to remove and clean residue thoroughly smooth sound condition (good old paint, if to continue the first coat Shipendec 120 ~ 150 grain sand paper solvents. If the poor state of the old paint, paint, varnish removal or abrasive deletes. Instructions, appropriate bare surface system performs these steps.
To provide a safe, slip proof textures not Island skid deck: deck, add Shipendec Pettit 9900 Skidless complex mixed. Continuous compound thoroughly dispersed, and stir the mixture remains in suspension. Court of two or more is recommended following appropriate application systems. The Court Shipendec 9900 Skidless composite) sprinkled or 9900 Skidless compound, and apply all the space you need without anti-slip surface wet of the broadcast Shipendec. After overnight carefully dry brush and combined all loose Skidless another thin apply one coat Shipendec surface. is pre-molded anti-slip embossment in 95 fiberglass Dewaxer deck wash surface. Abrade in thoroughly to remove bronze wool solvent residues clean area. Shipendec improved non-slip texture if necessary apply the additional two coats 9900 Skidless compound mixture.
Of the information provided here and Pettit courtesy reproduce. Wholesale Marine's reproduction 2010, June 8, this information.
This entry was posted on June 8, 2010 at 9: 52 a.m. and how to guides under the paint and submit. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response from your own site, or trackback.
No comments:
Post a Comment